The author is making several great observations relating to Tools You Need to Install a New Bathtub in general in this article which follows.
Installing a bathtub isn't precisely brain surgery, yet it does need strong plumbing, carpentry, and also often, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging job. If the old tub is conveniently accessible, the job can relocate speedily; if you need to open a wall to eliminate the old tub as well as position the new tub, the job is a lot harder. In either situation, the job is within a residence handyman's skills, although you will require a helper to move out the old bathtub and also set in the new one. Make sure you have actually certified yourself for the task and also are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This short article will certainly assist you set up a brand-new bathtub in your washroom if you have currently acquired a new tub and don't need to change the setup of your previous supply of water pipes.
Your tools and material checklist must comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last setting.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. When the supply pipelines have actually been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Before moving on to fit the new faucets, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, position the tub in the needed position. The wood boards are useful in equally spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto four small factors.
The following objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reviews degree.
To install faucets, fit the bottom of the outermost versatile tap connector to the ideal supply pipe by making a compression join; then do the same for the various other tap.
Activate the water and also check all joints and also brand-new pipework for leakages as well as tighten them if required. Load the tub as well as also inspect the overflow electrical outlet and the typical outlet for leakages.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the bath tub should wait up until the tub has actually been used at the very least when as this will resolve it into its last setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washing machines are in place between the faucet and the sink. Protect the faucet in place with the supplier provided backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind needs to be connected to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to split a stiff seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, causing issues with dampness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealant can split relatively early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about Installing A Bathtub? Give feedback down below. We would be delighted to listen to your views about this content. We are looking forward to see you back again before long. Please set aside a second to share this blog post if you enjoyed reading it. Many thanks for your time. Visit again soon.
Book An Estimate Now